- FAQ - Incorrect amount of land or die life & how to adjust
- FAQ - Set table to upper in the "SET" screen with manual Z axis
- FAQ - Table to next in the "SET" screen
- FAQ - How to set the taper settings in the "SET" screen
- FAQ - Wire cutter inspection and indexing
- FAQ - Checking wire guides for wear
- FAQ - Programing wire speed & wire tension into NC program
- FAQ - Taper and land and different offset amounts
- FAQ - Storing the cutting time into the header of the program
- FAQ - What can I use the string file for?
- FAQ - Reduce graphing time when using subroutines to do passes
- FAQ - G00 vs SF to achieve rapid movement
- FAQ - What causes slow cutting?
- FAQ - 4 axis programming
- FAQ - Maximum taper angle
- FAQ - Adjusting the AWT water jet
- FAQ - What are the spring loaded knobs located next to the AWT ?
- FAQ - Problems obtaining visible spark while doing wire adjustm
- FAQ - Explain the use of a header as opposed to not using one.
- FAQ - Offset & taper when you mirror a program
- FAQ - Incorrect taper
- FAQ - Wire speed
- FAQ - What is the approach pattern? How is it used?
- FAQ - Taper up or down
- FAQ - Disk requirements
- FAQ - Cutting faster than the book settings
- FAQ - Water resistivity meter settings
- FAQ - Setting TP & TN when the part is up off the table
- FAQ - Aligning the wire to the workpiece
- FAQ - Optional stops
- FAQ - How can I cut a part at an angle?
- FAQ - Lining up the AWT water jet
- FAQ - What are nests and loops?
- FAQ - How do T-program & T-next work in the graph screen?
- FAQ - Why would I want to deactivate the AWT unit?
- FAQ - Printing out the program after saving it to the disk
- taper cutting
- Training
- Pitting / rust on workpiece , bad on long cuts
- Sodick programs
- Cutting Parameters for WireEDM on Inconel Matl- SodickA500
- cutting parameters for cutting a profile in a rotating part
- Cheap Disk Drives
- PC interface
- discharge cable diagram
- Mega Spooler
- hot water, hot rooms
- Washboard finish on A280
- GRAF SAVING
- DROPPED OFFSET
- CUTTING CARBIDE BRAZED TOOLS
- cutting titanium and nitronic
- Corner Control
- Cast Steel
- Manual
- T84 dropped
- Ok Where are those online Manuals?
- RS232 Connection Problems
- Machine Hours
- Settings for cutting copper tungsten
- How to build a Network Interface
- wire hair ball?
- orange 280
- how to make permanent history list
- Settings for cutting Brass
- Heat Stop
- Fail to converting file.
- AQ325L - Cost of Ownership
- System error (12)
- sodick 330W
- cutting indistrial diamond
- settings for cutting titanium with a LN1W controler
- Programming
- Old Mark XXI problems
- sodick a320d markex
- 4 axis
- new type machine
- AP450L Water Request is?
- Wire Breakage
- CuMo Material
- taperdata program
- Sodick A500 W ( Mark XI ) Posts Processors
- sodick A-750
- work material getting rusty
- machine maintenance
- Error Message : Minus (-) Machine Coordination. How to fix it?
- Cutting Conditions
- Machine not cutting straight
- Maint. Screen Help
- Exercise on PC
- Resistivity
- air hydro unit
- air hydro unit
- The best machining condition table to cut aluminium sodick 320d
- Comprehensive Wire EDM Training
- CONDITION CODES FOR A530D W/ EX21
- device error
- A320D EX21
- 4 axis code for AQ325L
- M05 - Disable sensor
- Spesification EPOC 500
- Any Upgrade for Mark EX control-A320?
- only goes to zero
- Mark 11 upgrade
- repeat command
- Slow cutting
- Manual Input
- Wire does not cut
- graphics bar graph?
- RS-232 Settings
- Heath effects
- Post processer for A320 MKEX control
- Conditions to cut industrial diamons(GE CTC-002) with EPOC 300
- Wiring Diagram
- Taper w/land
- Backtension
- Need conditions for A500w
- A280L
- cutting conditions for CRS
- A530E Wire EDM Parts Manual
- Life of the Ball-Screw & Ball Slides
- Ver1.2 condition file
- Wore guide gets stuck opening
- Fixture Offsets???
- Lost XY power
- Head Crash
- Thermal error or UPS error
- Return to position after Halt
- Tension roller, A325 wire edm
- RS 232 settings
- VOLT METER
- MARK IX EDW Problem
- VOLT METER
- how to power up the machine
- Top and Bottom Different Profile
- Greasing the BF275
- MOVEMENT ERROR
- Cutting Taper on BF 275 with MARK IX
- Mark 11
- 6 degree taper on an AQ535L
- System Floppy
- BF-275 Mark IX User disk
- GW-40
- T CODES
- power settings
- resistivity setting for copper
- short circuit
- need instructions
- Boot error
- Small Parts
- Question about A500W ( Mark XI GOLD )
- Problem with A500W: Heat stop by overload
- Capability of Sodick BF 275 cutting ellipse curve without radius
- more line marks in single and douple pass
- 453W GW40 boot problems
- Filtration
- I have a BF 275 I need a new key pad . or the Little rubber cont
- Cutting Parameters for A500W
- Verify RS-232 Signal
- voltage too high
- backlash ajustement
- 4 axis programming sample
- Rules For Posting, Please Read!!!!!!!
- Lon
- A280L-Mark EX Alarm!
- u axis turn
- Graphite technology for wire EDM
- A320d
- Z+ height adjusted for magnet
- craters after 3 skims
- Program Help
- Change display from Metric to Inch
- Wire Path Display
- Sodick A325 Graph Mode
- Wire Edm small .016 hole.
- wire machine water level
- flush inverter box
- Replacement Monitor
- Help with part number
- A500 gold control
- Sodick 330W Fine Wire EDM
- I need information for sodick Gw-40
- A320D Mark EX
- Part # for Mark EX A280
- Flush Cups
- Short Circuit ERROR 164 on A530D Wire EDM
- I lose the starting point when you turn the machine mark II
- Error 164 Short Circuit on A520D Wire
- Help with hole problem
- Cutting Condtions for stsinless
- a280l system error 101
- 3rd and 4th pass
- 4320D Question
- Locked Out Keyboard?
- display maintenance page
- Trouble restarting A320D W/ EX21
- Water Seal Replacement on A535
- "Machine Overmoved" Error Message
- Help wanted --Cleveland OH area